Contact Form

Send your inquiry to Wuxi Rolls Excavator Parts Factory,China manufacturer.

Contact Info

Strict quality process control and management ensures
product quality and accountability.


Email : [email protected].NET


Worktime : 08:30-17:30 (Beijing Time)


  • Standard Penetration Test Driller's / Operator's Guide DSO

    Standard Penetration Test: Driller's / Operator's Guide DSO-98-17 byReclamation uses the Earth Manual procedure USBR 7015 to run the test - and if you haven't read it you shouldn't run the test. Theseout bit, or the end of the pilot bit in hollow-stem augers. In our testing procedures we state that if

  • Choosing the Appropriate Auger Size

    10″. 18″. The most common mistake when sizing forms and augers is choosing a curb form which is too small for a particular auger size. For example, a curb shape that is a simple rectangle 6″ wide x 4″ high would have a cross sectional area of 24 square inches. This puts it clearly in the 5″ diameter auger range.

  • Design and Construction of Auger Cast Piles

    diameters ranging from 12 to 36 in. and lengths. of up to 100 ft. In Europe with more recent. powerful rigs, diameters could go up to 60 in. The reinforcement is in the upper portion of the. pile for ease of installation and low bending. stresses are transferred below these depths. In.

  • DESIGN, INSTALLATION AND TESTING OF HELICAL PILES &

    Standard Helix Diameters CHANCE® Helical Products 16 (40) 1.385 (0.1286) 14 (35) 1.049 (0.0974) 12 (30) 0.771 (0.0716) 10 (25) 0.531 (0.0493) 8 (20) 0.336 (0.0312) 6 (15) 0.185 (0.0172) AREA ft2 (m2) DIAMETER in (cm) Standard Helix Sizes and Projected Areas

  • STIHL BT 120 C

    earth augers. Different models may have different parts and controls. See the appropriate section of your owner's manual for a description of the controls and function of the parts of your model earth auger. Safe use of an earth auger involves 1. the operator 2. the earth auger 3. the use of the earth auger. THE OPERATOR Physical Condition

  • Earth Auger Bits | Premier Attachments

    An additional benefit of the two-step design is that it helps eliminate air pockets typically produced when holes are dug with a conventional flat-bottom earth auger. The overall length of these augers come in 3' and 4'. Available diameters are 18”, 24”, 30”, 36”, 42”, and 48”.

  • Power Earth Auger Buying Guide

    A one-person auger is likely to run on a two-cycle engine, which requires a gas/oil mix. Two-person models are generally four-cycle and need no fuel mixing. Small bits are good for setting steel T-posts or U-posts. Wider and longer bits are available (the standard is 10-inch diameter and 36-inch drilling depth).

  • Verve Auger | DIY at B&Q

    I augered holes 500mm deep, but it can probably go to 800mm - 1m deep. A couple of tips: 1) wear protective gloves with a decent grip, otherwise you'll get blisters. 2) The description doesn't give the width of hole it makes - they are approximately 150mm (6 inch in old money) in diameter.

  • grainaugers.com

    MK80 x 51-71ft Auger Assembly & Operation Manual; MK100 x 51-81ft Auger Assembly & Operation Manual; MK100 & MK130 Plus x 91-111ft Auger Assembly & Operation Manual; MKX 130 Series; MKX130 (64, 74ft) Auger Assembly & Operation Manual; MKX130 (84, 94, 114ft) Auger Assembly & Operation Manual; MKX130 Right Angle Drive Kit Installation Instructions

  • Augers, Extensions, Points & Blades| Little Beaver

    Diameter Sizes (Standard Auger): 1.5″ 2″ 3″ 4″ 5″ 6″ 7″ 8″ 9″ 10″ 12″ 14″ 16″ Heavy-Duty Snap-On Augers When drilling in rocky soils, heavy-duty augers are recommended.